Q U I C K S TA R T M A N UA L 1. Rules for Safe Marker Handling
IMPORTANT: Never carry your Marker uncased when not on a playing field. The non-playing public and law enforcement personnel may not be able to distinguish between a paintball marker and firearm. For your own safety and to protect the image of the sport, always carry your Marker in a suitable marker case or in the box in which it was shipped. Read the entire manual before loading, attaching a propellant source or in any way attempting to operate any Empire BT paintball marker.
2. Getting Started
Do not install an air cylinder or load paintballs into your Marker until you feel completely confident with your ability to handle your Marker safely.
Safety ON
Safety OFF
Keep your finger out of the trigger guard and away from the trigger, point the muzzle of the marker in a safe direction at all times. Keep the marker in SAFE mode or with the Safety ON until ready to operate. Remember that the ultimate safety device is YOU, the operator. Safe Mode In this manual, you will see the term “SAFE” mode. The Safety should be set to SAFE (red marking on the safety will not be visible). Make sure your marker is set to SAFE when indicated to do so. (Fig. 1.0, 1.1) Barrel Installation Make sure the marker is degassed, hopper removed, no paintballs in the feed port or breech and the marker is set to SAFE mode. 1. Place the threaded end of the barrel into the front opening of the marker body. (Fig. 1.2) 2. Turn the barrel clockwise until it stops (do not over tighten). 3. Install a barrel blocking device. This can be a barrel plug or other such device that prevents the accidental discharge of a paintball.
Feed Elbow Installation 1. Press and hold the retention button located on the side of the Slide Away™ elbow. 2. Place the elbow onto the narrow section of the top Picatinny rail. (Fig. 1.3) 3. Slide the elbow along the Picatinny rail until it lines up with the feed hole on the right side of the Receiver. 4. Check that the elbow is locked in place and properly aligned. Note: The spring-loaded retention button must line up in a gap on the Picatinny rail.
Standard Loader/Hopper Installation 1. To install a loader, check the Slide Away™ elbow and loader to make sure they are free from debris and obstructions. 2. Position Slide Away™ elbow onto your marker’s receiver. 3. Release the Clamping Arm to allow the loader to slide into the top of the elbow. 4. Press the loader into the opening of the Elbow until it stops. 5. Align the loader so that the lid is pointing to the rear and the loader is parallel with the marker. 6. Clamp the loader in place using the clamping arm. Do not over tighten. Note: It might be necessary to adjust the clamping feed elbow screw to fit your loader. Using a 3/32” hex wrench, turn the screw clockwise to increase the clamping force or counter-clockwise to decrease the clamping force.
Air Cylinder Installation Consult the store where you purchased your Empire BT marker or a recognized and competent air smith for instruction in the safe handling of compressed-air or CO2 cylinders before purchasing or connecting one to your Empire BT marker. Before Pressurizing Your Marker 1. Check to make sure that you and anyone within range are wearing eye protection designed specifically for paintball. 2. Double check that all screws are tightened and no parts are loose before installing your tank. 3. Ensure you have a barrel plug or another barrel blocking device installed. 4. Make sure there are no paintballs in the marker. 5. Set the marker to SAFE mode. Pressurizing Your Marker 1. While pointing the marker in a safe direction, cock the marker by pulling the T-handle, located in the rear of the body, back until it clicks and stops. 2. Release the cocking handle, the marker is now cocked. 3. Locate the Air Source Adapter (ASA) located at the base of the pistol grip. 4. Position the Empire BT marker so that the ASA is pointed upwards while keeping the muzzle of the marker pointed in a safe direction. 5. Insert the threaded cylinder valve end into the ASA. (Fig. 1.4) 6. Without forcing the cylinder, twist the cylinder clockwise and allow the threads to draw the cylinder into the marker until it stops. Your marker is now gassed and charged. Notes: • Remember compressed air, nitrogen systems, and CO2 cylinders can be extremely dangerous if misused or improperly handled. Use only cylinders meeting D.O.T., TC, Pi or regionally defined specifications. • Never disassemble your tank or tank regulator. Only a qualified and trained technician should perform work on your tank or tank regulator. • Never add lubrication or grease into the fill adapter of your tank regulator.
Loading Paintballs Empire BT markers use .68 caliber, water-soluble paintballs, readily available at paintball pro-shops, commercial playing fields and many sporting goods stores. The paintballs are fed from the loader through the feed elbow into the breech of the marker. 1. Make sure the marker is set to SAFE mode. 2. Put on eye protection designed specifically for paintball and make sure that anyone within range of the marker does the same. 3. Load quality .68 caliber paintballs into your loader/hopper (leave some room for paintballs to move about inside the loader).
3. Firing Your Marker
1. Place the empty loader onto the marker 2. Be sure that it is securely in place. 3. Cock the marker. 4. Apply the air cylinder, pressuring the marker. 5. Put the paintballs into the loader. 6. Remove the barrel plug or other barrel blocking device. 7. Aim the Empire BT marker in a safe direction. 8. Set the Safety to the Fire position. 9. Aim the marker at the target. 10. Place your finger on the trigger. 11. Pull the trigger with a smooth squeezing motion.
4. Velocity Adjustment
Always check the velocity of the marker prior to playing paintball. Different playing fields may have different maximum velocity limits. At no time should you shoot at velocities above 300 feet-per-second (92 m/s). 1. While…
The first 1053 words, extracted from the PDF. Read the full manual above, or download it.