Dye DM6 Manual - English

OWNER’S

MANUAL

TABLE OF CONTENTS

QUICK REFERENCE PAGE 02

IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES PAGE 03

BOARD SETTINGS AND FUNCTIONS PAGE 04

INCLUDED WITH YOUR DM6 -

FUSE BOLT PAGE 08

DM6 Marker Allen tool set including 1/16”, 5/64”, 3/32”, 1/8”, 5/32”, 3/16” and 1/4” 1 oz. Dye Slick Lube™ Parts Kit Barrel Sock Owner’s Manual Warranty Card

LOW PRESSURE REGULATOR (LPR) PAGE 10

ON/OFF VALVE PAGE 11

ADDITIONAL RECOMMENDED TOOLS < <

HYPER2™ PAGE 12

3/8’ Allen wrench 5/16” Allen wrench Canned Air

ANTI CHOP EYES/ BALL DETENTS PAGE 13

S P E C S > > W E I G H T W I DT H L E N G T H H E I G H T E F F I C I E N C Y B AT T E R Y L I F E O P E R AT I N G P R E S S U R E C YC L E P R E S S U R E M A X R AT E O F F I R E B A R R E L T H R E A D

ULTRALITE FRAME PAGE 14

EXPLODED VIEW PAGE 15

TROUBLE SHOOTING GUIDE PAGE 16

WARRANTY INFORMATION PAGE 17

Q U I C K R E F E R E N C E - U s i n g yo u r m ar k e r

WA R N I N G

Air Supply - The DM6 should be operated using air/nitrogen gas only. This air needs to be supplied to the Hyper2™ in-line regulator at a regulated pressure of no more than 850 psi. The Hyper2™ in-line regulator comes factory preset at 145psi. Turning On Your DM6 - The DM6’s power is controlled with two buttons on the back side of the grip frame. The top button turns the marker on and off, while the bottom button turns the eye on and off. To turn the DM6 ON, press and hold the power button until the LED lights turn blue. The LED’s in the grip will illuminate during the boot sequence. NOTE: If the eye is not working properly, try replacing the battery. Blue Red Green Blinking Red Blinking Green Blinking Blue -

Boot Sequence Breech is clear, no ball (eye on) Ball in breech, ready to fire (eye on) Eye is off Eye failure (see DM6 Board, page 5) Indicates a low battery, battery should be changed as soon as possible

On/Off - The On/Off knob is located under the barrel at the front of the DM6. To turn the gas on, turn the knob counter-clockwise. To turn the gas off, turn the knob clockwise. All gas will vent from the DM6 when the knob is turned off. Air may still be present in the LPR and solenoid after the air has been vented from the marker by the on/off. Be sure all air has been vented by discharging the marker in a safe direction. If servicing the marker, removal of the bolt will also allow any trapped air to escape. LPR - The LPR is pre-set from the factory at approximately 75-80 psi and should need no adjustment out of the box. If fine tuning adjustment is desired or needed, you must be sure that you are adjusting the LPR correctly. See page 10 for detailed instructions. If the LPR is improperly adjusted, you could dramatically hinder the DM6’s performance or prevent the marker from functioning at all. NOTE: Turning the adjustment screw clockwise, or in, will lower the LPR’s output pressure. Turning the adjustment screw counterclockwise, or out, will raise the LPR’s output pressure. Hopper - To get the best performance out of your DM6, it is recommended that you use a motorized loader. Preferably one that force feeds the paint really, really fast! Feed Neck - To secure your loader into the adjustable feed neck simply tighten the thumbscrew by turning it clockwise. To loosen, turn the thumbscrew counter clockwise. Be careful not to over-tighten the collar as it can cause the neck to break. Adjusting Velocity - The velocity is adjusted through the Hyper2™ in-line regulator. The Hyper2™ in-line is preset from the factory at approximately 145 psi. This pressure setting should have the marker shooting at about 285fps. Your paint-to-barrel fit will also have a noticeable affect on your velocity. Make sure that the paintball fits into the barrel loosely but does not drop through. NOTE: For the Hyper2™, turning the adjustment screw clockwise, or in, will lower the output pressure, decreasing the velocity. Turning the adjustment screw counterclockwise, or out, will raise the output pressure, increasing the velocity.

NOTE: If the battery is too low, it may not be able to power the solenoid correctly. This will affect your DM6’s velocity, causing it to become inconsistent and/or low.

The DM6 marker is not a toy. Misuse may cause serious injury or death. Please read, understand and follow the directions in the DM6 owner’s manual. Eye protection that is designed specifically for paintball and meets ASTM/CE standards must be worn by user and persons within range. Recommend 18 years or older to purchase. Must have adult supervision if under 18. Always treat the DM6 marker as if it were loaded and able to fire. Only use compressed air or nitrogen gas in the DM6 marker. DO NOT USE CO2. Do not exceed 850 psi input pressure. Ensure all air lines and fittings are tightened and secured before gassing up the DM6. Always chronograph the DM6 marker before playing paintball. Never shoot the DM6 marker at velocities in excess of 300 feet per second, or at velocities greater than local or national laws allow. Never look into the barrel or breech area of the DM6 when the marker is switched on and able to fire. Always fit a barrel blocking device to your DM6 when not in use on the field of play. The owner’s manual should always accompany the product for reference or in the event of resale and new ownership. Do not point the DM6 marker at anything that you do not intend to shoot. Do not shoot at people…