Brass Eagle After Burner Diagram - English

Flow Connector Fitting

Flow Connector Nut/Fitting

Set up a table with plenty of space to work. You will need a 1/8" allen wrench, 3/16" allen wrench, a 5/16" wrench, long nose pliers, a keyhole or rounded file, a phillips head screw driver, a small flathead screwdriver and some gun oil.

READ EACH STEP COMPLETELY BEFORE PERFORMING STEP

Piston/Fitting

Flow Control Exterior Assembly

Front Sight Receiver Reference Feeder Housing Front Rear Sight Sight Upper Receiver Bolt

Step 1: Prepare Marker for Upper & Lower Receiver Disassembly To do so, you must: (1- unload your marker; (2- remove CO2 source; and (3- uncock marker before further disassembly. 1) Unload your marker: first remove the hopper. Then, point your marker in a safe direction and fire several times to be sure there are no balls left in the feeder or lodged in the chamber. 2) Remove tank: To remove a charged CO2 cylinder, turn the cylinder approximately 3/4 of a turn counterclockwise or out. This allows the tank pin valve to close so that no CO2 will enter the marker. Point the marker in a safe direction and fire the remaining CO2 in the marker by pulling the trigger until the marker stops firing. (This may take 4-5 shots) If your marker keeps firing after you have turned the tank 3/4 of a turn, the tank pin valve has not closed yet and you may have to turn the tank counterclockwise a little further. If you turn the tank 3/4 of a turn and it begins to leak before you pull the trigger you have turned it too far and may have damaged the tank o-ring. 3) Put the marker in the uncocked position: hold the bolt cocking handle back - then pull the trigger and release handle forward to un-cock the marker.

Step 2: Remove Gas Line and Lower Receiver from upper receiver 1) To remove gas line from upper receiver: Remove push pin (#1) in front of gas line plug from upper receiver, release Tombstone Latch and gas line will pull out. 2) To detach lower receiver: Remove 2 lower receiver push pins (#2 & #3) to detach from upper receiver.

Step 3: Prepare Lower Receiver for Trigger Response Piston/fitting installation

1) Remove gas line adapter bolt (#5). 2) Remove trigger assembly from grip: Push Safety out left side of lower receiver and pull up on trigger assembly. 3) Remove 3 grip screws and pull halves apart. 4) Remove tab in right grip half with long nose pliars. Carefully grip the tab and bend it towards the inside of the < TAB right grip half to remove it. NOTE: Bending tab < towards the outside could damage the right grip. 5) Carefully debur jagged edge where tab File 1234567890123456 1234567890123456 was removed with file. File edges 1234567890123456 until New Flow Connector nut/fitting 1234567890123456 1234567890123456 1234567890123456 fits easily into newly created opening 1234567890123456 1234567890123456 1234567890123456 1234567890123456 when assembling upper & lower 1234567890123456 receivers later in installation. Clean 1234567890123456 grip half of any filings before proceeding.

Gun Oil

Barrel & Adapter

Tombstone Latch

Front Grip Grip Bolt & Washer (not visable) Note: grip bolt is shortest bolt

Tombstone Adapter

Gas Line

Lower Receiver

Step 4: Installing Piston/Fitting Into Lower Receiver. 1) Position the assembled piston/fitting Tab removed into the right lower receiver half. 2) Place trigger guard in position and reassemble the Lower Receiver Halves with 3 lower receiver screws. 3) Reinstall the Trigger Group Assembly into the grip and position so you can insert the safety from left side. 4) Insert tank adapter and secure with tank adapter bolt.

Step 5: Prepare Upper Receiver for Response Trigger Parts Installation 1) Remove drive assembly. (front bolt, power tube, valve, rear bolt, linkage arm, drive pin guide, drive spring and end cap assembly): a) Screw velocity screw in past receiver. b) Remove last push pin (#4) holding end cap in place. c) Pull end cap out and tilt marker up, drive assembly parts should slide out the back. 2) Remove Rear Site: Pull up and out. 3) Remove front grip: Remove bolt/washer inside front grip with 3/16” allen wrench (note: shortest bolt) 4) Remove feeder banjo fitting bolt from upper receiver and carefully slide cylinder hose off it. This banjo fitting will not be reinstalled. 5) Remove Feeder Housing: With 3/16” allen wrench remove bolt #6 from left front side of upper receiver. 6) Remove front sight: Remove front sight bolt just below front sight and slide sight upward. 7) Barrel/Adapter Removal: Loosen remaining 6 upper receiver bolts and twist barrel counterclockwise to remove barrel and adapter as one unit. 8) Remove 6 upper receiver bolts & seperate halves.

260/749-6022 • 800/533-4831 • FAX: 260/749-6619 • 3518 Adams Center Road • Fort Wayne, IN 46806 • INTERNET: www.tippmann.com

WARNING: DO NOT OPERATE THIS MARKER WITH PARTS MISSING OR DAMAGED. If a part is lost or found to be damaged, obtain a replacement part before continuing reassembly.

Step 7: 1) Insert Install 2 new the Flow Connector parts into Bolt as the left shown. upper receiver half.

2) Place the Flow Connector fitting (largest opening first) on to Flow Connector Bolt as shown.

Align two upper receiver halves to identify and remove nut from lower back right half where Flow Connector Bolt will protrude (new Flow Connector Nut/Fitting will be installed at this point later in - Step: 9, #9).